Skip to content

how do I make a hummingbird feeder?

A hummingbird feeder is a great way to attract these beautiful creatures to your yard or garden. You can buy a hummingbird feeder at your local hardware or home improvement store, or you can make your own. Homemade hummingbird feeders are easy to make and can be just as effective as store-bought feeders. Plus, they’re a lot cheaper! To make a hummingbird feeder, you will need:

• A clean, empty plastic bottle

• A drill

• A small funnel

• A piece of wire

• A red ribbon or tape

• Hummingbird nectar (sugar water) Start by drilling two small holes in the plastic bottle, near the top. These holes will be for the wire hanger. Next, use the funnel to pour nectar into the bottle. Fill the bottle almost to the top. Thread the wire through the holes

1. Gather the necessary supplies.

In order to make a hummingbird feeder, you will need a few supplies. You will need a clean, empty bottle with a narrow neck, a hummingbird feeder kit, sugar, and water. First, you will need to clean the bottle and remove the label.

Next, you will need to assemble the feeder kit according to the instructions. Once the feeder is assembled, you will need to mix sugar and water together in a ratio of 1:4. Once the sugar water is mixed, you will need to fill the feeder up to the fill line and screw on the cap. Now your hummingbird feeder is ready to use!

how do i make a hummingbird feeder

2. Cut the plastic bottle in half.

If you want to make a hummingbird feeder, one of the first steps is to cut a plastic bottle in half. You can use any type of plastic bottle for this, but it needs to be cut evenly so that the feeder will hang level. Once you have cut the bottle in half, you will need to drill a hole in the base of each half. This is where the hummingbird will insert its beak to feed.

3. Poke holes in the bottle top.

If you want to make a hummingbird feeder, one of the first steps is to poke holes in the bottle top. This will allow the nectar to flow out and provide food for the hummingbirds. You can use a skewer or a toothpick to make the holes. Just be sure to make them big enough so that the nectar can flow freely.

4. Thread the wire through the holes.

To make a hummingbird feeder, first, gather the supplies you will need: a glass bottle, a drill, wire, pliers, and scissors. Next, clean the bottle and drill four small holes around the top. Thread the wire through the holes, making sure to leave enough wire at the top to create a hanger. Cut a small piece of wire and create a hook to secure the bottle to the hanger. Finally, mix sugar water and fill the bottle. Hang the feeder outside and wait for the hummingbirds to come!

5. Attach the wire to the hanger.

In order to attach the wire to the hanger, you will need to first locate the end of the wire that is not attached to the feeder. Once you have found this end, thread it through the hanger so that the end with the feeder is facing downwards. You may need to adjust the position of the hanger so that the feeder is level. Once you are satisfied with the placement, you can use tape or a twist tie to secure the wire to the hanger.

6. Fill the bottle with sugar water.

Assuming you would like a paragraph about how to make a hummingbird feeder: To make a hummingbird feeder, you will need a clear plastic bottle, a drill, a 1/4 inch drill bit, a hammer, a nail, wire, scissors, and a funnel. You will also need a 1:4 ratio of sugar to water. Start by drilling a hole in the center of the bottle cap.

Next, use the hammer and nail to make a small hole in the side of the bottle. Cut a piece of wire that is long enough to go through the holes in the bottle cap and side of the bottle, and then twist the ends of the wire together. Next, use the funnel to pour the sugar water mixture into the bottle. Screw the bottle cap back on, and then hang the feeder from the wire. Be sure to place the feeder in a shady spot, and keep an eye on the sugar water level, replenishing as necessary.

7. Hang the hummingbird feeder.

Assuming you would like tips on hanging a hummingbird feeder: The best way to hang a hummingbird feeder is to use a wire hanger. You will need to make sure that the hanger is securely fastened to the feeder so that it does not fall and break. You can also use a suction cup to secure the feeder to a window.


You can make a hummingbird feeder by filling a small container with sugar water and hanging it from a tree or other structure.

Leave a Reply

Your email address will not be published. Required fields are marked *